**TSGENCO AE Syllabus / TSGENCO AEE Syllabus / TSGENCO AE & AEE, JLM Syllabus / TSGENCO Syllabus Download at www.tsgenco.telangana.gov.in.**

Telangana State Power Generation Corporation Limited (TSGENCO) is going to Junior Linemen (JLM) / AE & AEE General Recruitment Examination 2020. TSGENCO AE & AEE is Published in Notification at Official Website www.tsgenco.telangana.gov.in.

TSGENCO AE & AEE , Junior Linemen (JLM) Syllabus has been Published by Telangana Power Generation Corporation Limitedonly. TSGENCO AE AEE Recruitment 2020 Applicants You can Download Syllabus Our websites also

- TSGENCO AE Model Papers 2020
- TSTRANSCO AE Model Papers 2020
- TSNPDCL AE Model Papers 2020
- TSSPDCL AE Model Question Papers 2020
- TSTRANSCO AE & AEE Syllabus 2020
- TSSPDCL AE & AEE Syllabus 2020
- TSNPDCL AE & AEE Syllabus 2020

**Syllabus for Electrical Branch – Section-A (80Marks)**

**Electrical Circuits and Networks – Kirchhoff’s laws, mesh and node analysis, network theorems, **sinusoidal steady stateanalysis of single phase and three phase circuits, resonance, transient response of RL,RC,RLC circuits for different inputs, two-port networks, Two element network synthesis.

**Control Systems **– Modelling of physical systems, Block diagrams and signal flow graphs, Time andfrequency domain analysis, Steady state errors, Routh’s criterion, Nyquist and Bode plots,compensation, root loci, elementary ideas of state variable analysis, control system scomponents

**Measurements and Instrumentation **– SI units, measurement of current, voltage, power, power-factor and energy.Measurement of resistance, inductance capacitance and frequency-bridge methods,transducers and their applications to the measurement of non-electrical quantities liketemperature, pressure, strain, displacement etc., cathode ray oscilloscope, Instrument Transformers

**Analog and Digital Electronics **– Characteristics of diodes, BJT, FET,SCR, Amplifier biasing, equivalent circuits,frequency response, feedback amplifiers, power amplifiers, oscillators, operationalamplifiers and applications, wave shaping circuits, multi-vibrators, flipflops, universal gatecombinational circuits, A/D and D/A converters

**Electrical Machines** – Single phase transformer, equivalent circuit, tests, regulation and efficiency, three-phase transformer connections parallel operation, autotransformer, principle of energy conversion, winding of rotating machines, DC generators, and motors, characteristics, starting and speed control, three-phase induction motors performance characteristics, starting and speed control, single-phase induction motors, synchronous generators, performance, regulation, parallel operation, synchronous motors, starting characteristics and applications, synchronous condensers, fractional horsepower motors, permanent magnet and stepper motors

**Power Electronics and Drives **– Characteristics of Power Electronic devices, phase control,bridge converters, choppers and inverters, basic concepts of adjustable speed drives, Control of Induction & Synchronous Motors.

**Power Systems **– Electrical power generation thermal, hydro, nuclear: transmission line parameters;steady state performance of overhead transmission lines and cables, surge propagation,distribution systems, insulators, bundle conductors, corona, and radio

interference effects;per-unit quantities: bus admittance and impedance matrices: load flow: voltage control andpower factor correction; economic operation, symmetrical components, analysis ofsymmetrical and unsymmetrical faults.

**Switchgear protection** – Principles of over current, differential and distance protections, circuit breaker, concept of system stability, swing curves and equal area criterion. Power System Operation & Control, Relays, Protection for Generator, Transformers, feeder and Busbars, Grounding, Protection against Over Voltages, Batteries and Battery Chargers.

**Power Plant Engineering** – Basic of Prime movers, Pumps, Boilers & Turbines, Rankine Cycle, Basics of SM & FM, Introduction to Quality management and Environmental Protection.Steam Power Plant, Combustion Process, Gas Turbine Plant, Direct Energy Conservation, Hydro Electric Power Plant & Power from Non-conventional sources, Power plant economicsCapital

cost, Investment of fixed charges, operating cost, arrangements for power distribution, load curves, connected load, maximum demand, demand factor, average load, load factor, diversity factor, Environmental considerations- Effluents from Power Plants and impact of environment, Pollution and pollution standards-Methods of pollution control.

**Syllabus for Mechanical branch – Section-A (80Marks)**

**Strength of Materials** – Simple stresses and strains Hooke’s law, elastic constants, stress strain curve ofmild steel bars of uniform strength, compound bars, temperature stresses, stresses on oblique planes-principal stresses and strains, Mohr’s stress circle, shear force andbending moment diagrams for beams, bending and shear stresses in beams,deflections of beams, columns and struts, strain energy, torsion of circular shafts andsprings.

**Fluid Mechanics and Machinery **– Basic fluid properties, fluid static-pressure measurements, buoyancy andflotation, fluid kinematics, fluid dynamics-Euler’s Bernoulli’s and Impulse momentumequations, laminar and turbulent flows, flow through pipes and losses in pipes, bends,boundary layer theory, compressible fluid flow, impact of jets, Hydraulic turbines andpumps, Ram, Accumulator and intensifier.

**Material science and metallurgy** – Structure and properties of engineering materials, bonding in solids,imperfections in crystals and metals, structure of alloys, manufacture of iron and steel,heat treatment, alloy steels, principles of powder metallurgy

**Theory of Machines** – Displacement, velocity and acceleration analysis of plane mechanisms, dynamicanalysis of slider-crank mechanism, gear trains, flywheels.Vibrations-Free and forced vibrations, effect of damping, resonance, vibration isolation,critical speeds of shafts

**Design of Machine elements** – Design for static and dynamic loading failure theories, fatigue strength, S-Ndiagram, design of joints, shafts, bearings, gears, brakes, clutches, screws, springs,cranks, piston, gyroscopes, balancing and governors.

**Heat Transfer **– Various modes of heat transfer, fins, heat exchangers, LMTD & NTU methods,unsteady state heat conduction, dimensionless parameters, free and forced convectiveheat transfer, thermal boundary layer, heat transfer in flow-over flat plates and throughpipes, effect of turbulence, radioactive heat transfer, shape factors, network analysis,condensation and boiling

**Thermodynamics and Applied Thermodynamics** – Zeroth, first and second laws of thermodynamics, thermodynamics systems andprocesses, Carnot cycle, Air-standard cycles, irreversibility and availability propertiesof pure substances, psychometry, Refrigeration and Air conditioning, workingprinciples and their applications.Classification of compressors and its working principles, rating of fuels, lubrications, Ignitionsystems.

**Turbo Machines **– Working principles of gas turbines, steam turbines, Rankine’s cycle. ModifiedRankine’s cycle, jet propulsion and nozzles.

**Metal cutting and machine tools** – Mechanics of machining, single and multi point cutting tools, tool geometry , toollife wear, cutting force analysis, micro finishing machines-EDM, ECM and USM, NCmachines, jigs and fixtures. Standards of measurements, limits, fits, tolerances, linearand angular measurements, comparators, lathes, drilling, shaping, planning, milling,gear cutting. Broaching and grinding machines.

**Foundry, Welding and Forging** – Design of patterns moulds and cores, solidification, design consideration ofrunner, riser and gate. Physics of welding, types of welding and their principles,brazing, soldering, adhesive bonding, Fundamental of hot and cold working processes,forging, rolling, extrusion, drawing, shearing and bending

**Production and operation management **– Plant layout, material handling, production planning and control, materials,management and work studies, inspections, quality control, cost analysis, operationresearch, basic concepts of CAD/CAM, inventory control.

**Basic Electrical Engineering** – Electrical Circuits-Basics, Ohm’s Law, Kirchhoff’ Law, Inductive & Capacitive Networks, Series & Parallel Circuits, Star& Delta Transformers, Instruments-Basic Principles of indicating instruments, PMMC & Moving Iron Instruments, DC Machines-DC Generator, DC motors and their applications, Transformers-Operation, EMF Equation, Losses, efficiency & Regulation, AC Machines-Operation of Synchronous and Induction motors, their Characteristics & applications.

**Power Plant Engineering** – Steam Power Plant, Combustion Process, Gas Turbine Plant, Direct Energy Conservation, Hydro Electric Power Plant & Power from Non-conventional sources, Power plant economics-Capital cost, Investment of fixed charges, operating cost, arrangements for power distribution, load curves, connected load, maximum demand, demand factor, average load, load factor, diversity factor, Environmental considerations- Effluents from Power Plants and impact of environment, Pollution and pollution standards-Methods of pollution control

**Syllabus for Electronics branch: Section-A (80Marks)**

**Basics of Circuits and Measurement Systems** – Kirchhoff’s laws, mesh and nodal Analysis, Circuit theorems. One-port and two port Network Function. Static and dynamic characteristics of Measurement Systems. Error and uncertainty analysis. Statistical analysis of data and curve fitting

**Transducers, Mechanical Measurement and Industrial Instrumentation** – Resistive, Capacitive, Inductive and piezoelectric transducers and their signal conditioning. Measurement of displacement, velocity and acceleration (translational and rotational), force, torque, vibration and shock. Measurement of pressure, flow, temperature and liquid level. Measurement of pH, conductivity, viscosity and humidity

**Analog Electronics & Digital Electronics** – Characteristics of diode, BJT, JFET and MOSFET. Diode circuits. Transistors at low and high frequencies, Amplifiers, single and multi-stage. Feedback amplifiers. Operational amplifiers, characteristics and circuit configurations, Instrumentation amplifier. Precision rectifier. V-to-I and I-to-V converter. Op-Amp based active filters. Oscillators and signal generators. Combinational logic circuits, minimization of Boolean functions. IC families, TTL, MOS and CMOS. Arithmetic circuits, Comparators, Schmitt trigger, timers and mono-stable multi vibrator. Sequential circuits, flip-flops, counters, shift registers, Multiplexer, S/H circuit, Analog-to-Digital and Digital-to-Analog converters. Basics of number system. Microprocessor applications, memory and input-output interfacing, Microcontrollers

**Signals, Systems and Communications** – Periodic and aperiodic signals. Impulse response, transfer function and frequency response of first and second order systems. Convolution, correlation and characteristics of linear time invariant systems. Discrete time system, impulse and frequency response. Pulse transfer function. Infinite Impulse Resonance (IIR) and Finite Impulse Resonance (FIR) filters. Amplitude and frequency modulation and demodulation. Sampling theorem, pulse code modulation. Frequency and time division multiplexing. Amplitude shift keying, frequency shift keying and pulse shift keying for digital modulation.

**Electrical and Electronic Measurements** – Bridges and potentiometers, measurement of R, L and C. Measurements of voltage, current, power, power factor and energy. A.C & D.C current probes. Extension of instrument ranges. Q-meter and waveform analyzer. Digital voltmeter and multimeter. Time, phase and frequency measurements. Cathode Ray Oscilloscope. Serial and parallel communication. Shielding and grounding.

**Control Systems and Process Control** – Feedback principles. Signal flow graphs. Transient Response, steady-state errors. Routh and Nyquist criteria. Bode plot, root loci. Time delay systems. Phase and gain margin. State space representation of systems. Mechanical, hydraulic and pneumatic system components. Synchro pair, servo and step motors. On-off, cascade, P, P-I, P-ID, feed forward and derivative controller, Fuzzy controllers

**Analytical, Optical Instrumentation** – Mass spectrometry, UV, visible and IR spectrometry, X-ray and nuclear radiationmeasurements. Optical sources and detectors, LED, laser, Photo-diode, photo-resistor and their characteristics. Interferometers, applications in metrology. Basics of fiber optics. Microprocessor and Micro controller: Intel 8086/8088 architecture, segmented memory, Maximum and minimum mode of operation, addressing modes, instruction set, assembler directives, macros, procedures, assembly language programming using data transfer, arithmetic, logical, branching and string manipulation instructions. I/O interface , Interfacing with advanced devices, communication interface, micro controllers, difference between micro controllers and micro processor, 8051 real time control,

**Telecommunication, switching system and networks** – Evaluation of Telecommunications, basics & functions of switching systems, crossbar switching, electronic switching and digital switching, Telecommunications trafficcongestion, traffic measurement, queuing system, queues in tandem, delay table, application of delay formulae, switching networks, time division switching, control of switching system, signalling, packet switching, networks-Analog, integrated digital, cellular radio, intelligent, private networks, charging, rooting.

**Basic Electrical Engineering** – Electrical Circuits-Basics, Ohm’s Law, Kirchhoff’ Law, Inductive & Capacitive Networks, Series & Parallel Circuits, Star& Delta Transformers, Instruments-Basic Principles of indicating instruments, PMMC & Moving Iron Instruments, DC Machines-DC Generator, DC motors and their applications, Transformers-Operation, EMF Equation, Losses, efficiency & Regulation, AC Machines-Operation of Synchronous and Induction motors, their Characteristics & applications

**Syllabus for Civil branch: Section-A (80Marks)**

**Strength of materials and theory of structures** – Simple stresses and strains, Hooke’s Law, elastic constants, stress strain curve of mild steel stresses on oblique planes. Principal stresses and strains, Mohr’s stress circle, temperature stresses, compound bars, shear force and bending moment diagrams for beams, bending and shear stresses in beams, strain energy principles, torsion of circular shafts . Pure torsion and combined with bending and thrust, deflections of simple beams, thin and thick cylinders, columns and struts, direct and bending stresses, trusses, propped cantilevers and fixed beams, arches, cables and suspension bridges; moving loads and influence lines; static and kinematic indeterminacies, Continuous beams and portal frames movement distribution, Kani’s and matrix methods. Unsymmetrical Bending and shear Centre

**Reinforced Concrete** – Materials -properties, grades and tests, workability and mix design of concrete- basic concepts of working stress and limit state methods of design. Limit state design of beams, slabs, columns, footings. Circular and flat slabs, water tanks, bridges. IRC specifications and loadings, Slabs and T beam bridges, retaining walls, Pre-stressed concrete-basic concepts, losses and analysis and design of beams including end block.

**Steel structure **– Riveted and welded joints, Connections-eccentric and framed, simple and compound beams, tension and compression members, plate and gantry girders, roof trusses, plate girder and truss bridges, water tanks, roof trusses, tubular sections and design, transmission towers, column bases, plastic analysis, basic principles, theorems, methods of analysis, analysis and design of determinate and indeterminate beams and frames.

**Geo-Technical Engineering** – Origin and classification of soils, three phase system, basic definitions and relations, effective stress. Permeability, capillarity and seepage of soils, flow nets, flow through earthen dams, compressibility, consolidation and compaction of soils, shear strength, stability of slopes, earth pressures and retaining walls, stress distribution in soils, settlement analysis, subsurface exploration and site investigations, bearing capacity of Soils, shallow and deep foundations, pile foundations.

**Other Topics –** Elements of surveying-Chain, plane table, compass and theodolite, levelling, building materials and construction, formwork, CPM and PERT

**Fluid Mechanics and Machinery** – Properties of fluids, pressure measurement fluid statics, buoyancy and flotation, fluid kinematics and fluid dynamics, orifices and mouthpieces, notches and weirs, laminar and turbulent flows, flow through pipes, forces on immersed bodies, flow in open channels, impact of jets, Hydraulic turbines and pumps, dams, power houses, hydrology and hydro power plants.

**Environmental Engineering** – Objectives of Protected water supplies, Analysis of water, Classification, description and design of filtration, disinfection and softening processes, methods of layout of distribution pipes, Treatment of Sewage, Principles and design of screens, grit chambers, detritus tanks, sedimentation tanks, contact beds, trickling filters and activated sludge process, Methods of sludge disposal, sludge digestion tanks, principles and design of septic tanks.

**Hydrology & Water management** – Definition, relation to Engineering design, hydrological cycle, importance of hydrology abs its application in engineering. Definition & types of Rainfall, measurement of rainfall, types of rain gauges, network design, presentation of precipitation data, mean aerial rainfall isohyetal methods, depth- area- duration curve, dependable rainfall. Runoff process, factors affecting runoff, determination of runoff, importance of stream gauging, runoff formulae and runoff tables, definition & importance of flood studies, flood peak and flood hydrograph, methods of computing flood peak, empirical methods, rational formula, unit hydrograph method, flood frequency studies, weibul’s and Gumble’s extreme value methods, Statistical parameters, central tendency parameters, dispersion characteristics, skewness, probability distribution, discrete and continuous distribution, frequency analysis, log Pearson type III distribution, regression and correlation, standard forms of bivariate equation, multivariate linear regression and correlation , analysis of time series, selection of design return period, determination of permission risk.

**Basic Electrical Engineering** – Electrical Circuits-Basics, Ohm’s Law, Kirchhoff’ Law, Inductive & Capacitive Networks, Series & Parallel Circuits, Star& Delta Transformers, Instruments-Basic Principles of indicating instruments, PMMC & Moving Iron Instruments, DC Machines-DC Generator, DC motors and their applications, Transformers-Operation, EMF Equation, Losses, efficiency & Regulation, AC Machines-Operation of Synchronous and Induction motors, their Characteristics & applications.

**Power Plant Engineering **– Steam Power Plant, Combustion Process, Gas Turbine Plant, Direct Energy Conservation, Hydro Electric Power Plant & Power from Non-conventional sources, Power plant economics-Capital cost, Investment of fixed charges, operating cost, arrangements for power distribution, load curves, connected load, maximum demand, demand factor, average load, load factor, diversity factor, Environmental considerations- Effluents from Power Plants and impact of environment, Pollution and pollution standards-Methods of pollution control.

**General Awareness and Numerical Ability: Section –B (Common to All Streams) – Total 20 Marks.**

- Analytical &Numerical Ability
- General Awareness
- English
- Related to Telangana Culture, Movement
- Computer Knowledge

## Leave a Reply Cancel reply